Replace one-pole sum/diff filters with a proper 4th-order Butterworth
cascade (Q = 0.5412 / 1.3066) at 15 kHz. This reduces pilot tone
leakage from −4 dB to −12 dB at 19 kHz and suppresses the 38 kHz DSB
carrier from −9 dB to −32 dB, significantly improving stereo crosstalk.
Add a biquad notch at 19 kHz on the L+R channel to eliminate the residual
pilot tone that would otherwise be audible after downsampling to 48 kHz.
Replace nearest-neighbor (sample-hold) resampling with linear interpolation
inside WfmStereoDecoder. The output sample is now placed at the exact
fractional position between the two adjacent composite samples using the
phase accumulator state, removing timing jitter and harmonic distortion on
sustained tones.
Add DC blockers (pole at 0.9999, corner ≈ 0.75 Hz at 48 kHz) to all audio
outputs to remove carrier frequency-offset DC from the FM discriminator
without any audible bass roll-off.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Drop the now-unused rigctl_port local after removing\nthe shared rigctl listener path.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Remove the shared rigctl listener path so rigctl only\nruns as per-rig listeners configured through\nfrontends.rigctl.rig_ports.\n\nTighten client config validation to require at least one\nper-rig rigctl port when the rigctl frontend is enabled.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Make the primary SoapySDR DSP channel follow the tuned\nfrequency so RDS decoding stays aligned with the active\nfrequency rather than the hardware center.\n\nMove the default WFM deemphasis setting to server SDR\nconfig and default it to 50 us, then pass that value into\nthe SoapySDR backend.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Add server-side debug log when RDS data is decoded (PI, PS, PTY).
Extend the RDS panel with active mode, frame counter, and a raw JSON
dump of the last spectrum frame (bins excluded) to help diagnose why
RDS remains absent from the SSE stream.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Draw small peak markers on strong visible spectrum maxima\nso snap-tune targets are easier to spot.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Apply the same explicit height and padding rules to the\nAuto BW button as the Set button in the spectrum\ncontrols, including the mobile layout.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Add an RDS sub-tab to the Plugins panel showing PI code, PS name, PTY
number and name, decoder status, and a raw JSON dump of the latest RDS
data received via SSE. Also list the RDS decoder in the Overview tab.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Include the snapped peak signal level in the spectrum\nhover tooltip alongside the peak frequency.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
The FIR LPF cutoff was audio_bandwidth_hz/2; with wfm_bandwidth_hz=75000
this gave 37.5 kHz, stripping the 57 kHz RDS subcarrier before FM
demodulation. Clamp the IQ filter bandwidth to at least 130 kHz (cutoff
≥ 65 kHz) for WFM so the RDS subcarrier always reaches the decoder,
regardless of the configured audio bandwidth.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Add an Auto BW control that estimates a suitable\nreceive bandwidth from the live spectrum around the\ncurrently tuned peak and applies it to the server.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Update the local tuned-frequency state immediately after\nsuccessful set_freq requests so the marker and display stay\nin sync with click-to-tune, manual entry, and jog tuning.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Show snapped peak frequencies in the spectrum hover tooltip\nand move the bandwidth label to the bottom of the tuned\nfrequency marker.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Improve spectrum click-to-tune by snapping the selected\nfrequency to a nearby dominant local peak, making signals\neasier to select.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
In multi-rig mode, each RigInstanceConfig.audio.listen defaulted to
127.0.0.1 independently of the global [audio] listen setting, causing
per-rig audio ports to bind to localhost only and refuse connections
from remote clients.
Fix by passing cli.listen.or(Some(cfg.audio.listen)) as the listen
override, so the global address is always the fallback when --listen
is not supplied on the CLI.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Keep the top bar visible for unauthenticated users, but\nhide the rig selector until a session is established.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Keep the top bar visible while logged out, limit access to\nthe Main tab, and leave theme controls available while the\nrig selector stays disabled.\n\nRename the internal style ids from nord/arctic and\nmonokai/lime, including a compatibility remap for saved\nsettings.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Rename the Nord and Monokai theme labels in the web UI\nto Arctic and Brownie, and update the matching CSS\nsection comments.\n\nCo-authored-by: Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Only trx-rs.toml with [trx-server] / [trx-client] section headers is
now supported. Simplify ConfigFile trait to a single required method
section_key(); remove config_filename(), combined_key(), and
default_search_paths(). load_from_file() now errors when the expected
section is absent rather than falling back to flat parsing.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Add rig_ports map to RigctlFrontendConfig. When non-empty, one rigctl
TCP listener is spawned per entry instead of the single shared listener,
each routing commands to its assigned rig via rig_id_override on RigRequest.
Add rig_id_override: Option<String> to RigRequest so the remote client
can route individual requests to a specific rig without changing the
globally selected rig. build_envelope prefers the override when set.
Example config:
[frontends.rigctl]
enabled = true
listen = "127.0.0.1"
port = 4532
rig_ports.ft817 = 4532
rig_ports.airspyhf = 4533
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Remove the home-directory dotfile paths that predate the XDG layout.
Search order is now: CWD → ~/.config/trx-rs/ → /etc/trx-rs/, checked
for both the combined trx-rs.toml and the per-binary flat file at each
tier.
Update doc comments and tests accordingly.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Superseded by example_combined_toml() which now covers all use cases.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Both trx-server and trx-client now look for a combined trx-rs.toml
with [trx-server] and [trx-client] section headers respectively,
falling back to per-binary config files as before.
Search order per tier: combined trx-rs.toml → flat per-binary file,
checked in CWD, ~/.config/trx-rs/, and /etc/trx-rs/.
--print-config now outputs the config under the appropriate section
header so the combined file can be generated directly.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
sjg
