Tech 1: replace one-pole baseband LPF with FIR RRC matched filter
(alpha=0.75, 4-chip span) — largest single measured improvement per
empirical comparison (gr-rds RRC vs plain FIR: 32/38 vs 18/38 stations).
Tech 2: 19 kHz pilot x3 -> 57 kHz coherent carrier reference via the
triple-angle formula; fed from the WFM pilot Costas PLL when
pilot_lock_level > 0.5, clearing to NCO fallback otherwise.
Tech 3/7/8: OSD(2) soft-decision block decoder replaces hard CRC check.
Per-bit soft magnitudes accumulated in Candidate::block_soft[26].
decode_block_soft() searches Hamming distance 0/1/2 (352 trials total)
and returns the minimum Euclidean-cost valid codeword; ~2-3 dB gain.
Tech 4: 8th-order 57 kHz BPF (4 cascaded biquads at Q=5) in wfm.rs
replaces the previous single Q=10 biquad; ~6x steeper ACI stopband.
Tech 5: Costas loop with tanh soft phase detector drives the RDS carrier
NCO when no pilot reference is available (P+I, B_L ~20 Hz).
Tech 6: Block A PI field LLR accumulation — signed per-bit LLR summed
over 3 independent Block A observations before committing the PI value,
correcting weak-signal false locks without delaying strong-signal lock.
Tech 9: 8-tap complex CMA blind equalizer applied to IQ samples before
FM discrimination; constant-modulus error (|y|^2 - R^2) drives tap
adaptation without a training sequence, suppressing adjacent-channel
interference at the source.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Use saturating CAS loop in adjust_total_count to prevent AtomicUsize underflow, and cap history estimate at 500k entries.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
The map module was tagging all decode markers (APRS, AIS, VDES,
FT8/FT4/FT2/WSPR locators) with the global rig picker's active rig
instead of the actual source rig. This made the map's own rig filter
dropdown ineffective in multi-rig setups.
- Add rig_id field to all decode message structs (AisMessage,
VdesMessage, AprsPacket, CwEvent, Ft8Message, WsprMessage)
- Set rig_id on messages in audio_client before broadcasting, using
the actual rig connection identifier
- Update history collector to prefer message rig_id over the global
active rig fallback
- Pass rig_id through plugin normalize functions (AIS, APRS, VDES,
HF-APRS) so it reaches the map add functions
- Update all map marker functions (aprsMapAddStation, aisMapAddVessel,
vdesMapAddPoint, mapAddLocator) to use the message's rig_id with
fallback to the global picker for backward compatibility
https://claude.ai/code/session_015gC7axHk2jmp7HbFPdbivN
Signed-off-by: Claude <noreply@anthropic.com>
Drop the plugin loading infrastructure (libloading-based dynamic .so/.dylib/.dll
loading) from both trx-server and trx-client. The feature was unused and posed an
unnecessary security risk by executing arbitrary native code from disk.
Removed:
- src/trx-app/src/plugins.rs (plugin discovery, validation, FFI registration)
- examples/trx-plugin-example/ (cdylib example plugin)
- libloading dependency from trx-app
- load_backend_plugins / load_frontend_plugins calls from server and client
- Plugin documentation from README.md and CLAUDE.md
https://claude.ai/code/session_01DTEUpz3XPUeWmz74NeaFgb
Signed-off-by: Claude <noreply@anthropic.com>
Update all SDR command handlers in rig_task to access SDR methods via
ctx.rig.as_sdr() instead of calling them directly on RigCat. Query-only
SDR operations (filter_state, get_spectrum, get_vchan_rds) use
as_sdr_ref(). Non-SDR rigs now get proper not_supported errors.
https://claude.ai/code/session_01XzurkeuUmamBuhQwxVy7T4
Signed-off-by: Claude <noreply@anthropic.com>
Add an AtomicUsize total_count field to DecoderHistories, maintained by
record/prune/clear methods, so estimated_total_count() avoids 9 separate
mutex acquisitions. Also replace audio ring buffer .unwrap() calls with
.unwrap_or_else(|e| e.into_inner()) to recover from poisoned locks.
https://claude.ai/code/session_01XzurkeuUmamBuhQwxVy7T4
Signed-off-by: Claude <noreply@anthropic.com>
IQ-domain impulse noise blanker using exponential-smoothing RMS tracker. Samples exceeding threshold × running RMS are replaced with the last clean sample. Configurable via [sdr.noise_blanker] in TOML config and runtime via POST /set_sdr_noise_blanker API.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
When Device::new(args) fails, enumerate all available SoapySDR devices and
include them in the error message. Also hint that args are case-sensitive.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
When specific SoapySDR device args are provided (e.g. with a serial number),
fail hard instead of silently falling back to Device::new("") which opens
the first available device. This caused multi-device setups to bind both
rig instances to the same physical device.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Normalize tracked SPDX headers to the 2026 Stan Grams identity.
Co-authored-by: OpenAI Codex <codex@openai.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Delete trx-ft8 (C wrapper around ft8_lib + ft2_ldpc) and update
trx-server to depend on trx-ftx (pure Rust) directly. Removes
~2,900 lines of C code and all unsafe FFI.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Thread aprs_is_status through RigState, RigSnapshot, and the protocol
layer following the same pattern as pskreporter_status. Show the
connection target and callsign when enabled, or "Disabled" otherwise.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Query the device for AGC support via has_gain_mode and enable it
automatically at startup. Devices without hardware AGC fall back to
manual gain as before.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Invalidate main-decoder windows whenever the rig's main frequency
changes, including direct SetFreq, scheduler-driven retunes, and
external CAT retunes observed during polling.
The decoder loops now resubscribe their PCM receivers on reset and drop
results that finish after the reset sequence advances, preventing false
decodes from stale pre-retune audio.
Co-Authored-By: OpenAI Codex <noreply@openai.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add NEON (aarch64) vectorized paths mirroring the existing AVX2 paths:
- demod/math_arm.rs: replace the no-op placeholder with a full NEON FM
discriminator that processes 4 samples per iteration using a 7th-order
minimax atan polynomial and branchless atan2 with argument reduction,
matching the accuracy of the AVX2 path (max error ~2.4e-7 rad).
32-bit ARM retains the scalar fallback.
- dsp/filter.rs: add mul_freq_domain_neon() that deinterleaves 4 complex
pairs via vuzpq/vzipq, performs complex multiply with vmulq/vaddq/vsubq,
then reinterleaves. On aarch64 this path is always taken (NEON is
mandatory); scalar fallback remains for other targets.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
clamp_bandwidth_for_mode now floors AMC bandwidth at 9 kHz so that both
the sum (L+R) and difference (L−R) sidebands are always captured,
regardless of what the user or a set_filter call requests.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
RigMode::AMC was implemented but omitted from the supported_modes vec,
so the HTTP frontend never received it in capabilities and the mode
selector did not show AMC-QUAM.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
- remote_client tests: add missing server_connected field and import
AtomicBool in the test module
- pskreporter: replace map_or(true, …) with is_none_or and
repeat(x).take(n) with repeat_n(x, n)
- dsp.rs, scheduler.rs: suppress intentional too_many_arguments with
#[allow(clippy::too_many_arguments)]
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add a RigMode::AMC arm to encode_mode returning an Err so that
attempting to set C-QUAM on the FT-450D returns a descriptive error.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add RigMode::AMC to the None return arm of encode_mode so that
attempting to set C-QUAM on the FT-817 returns a descriptive error
rather than a compile-time non-exhaustive match.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add RigMode::AMC arm to default_audio_bandwidth_for_mode, returning
9_000 Hz (same as AM).
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add CquamDemod (demod/amcquam.rs) with first-order IIR carrier phase
tracker (τ = 50 ms) that rotates baseband IQ to align I with the sum
audio and Q with the difference audio, then DC-blocks each channel to
yield L/R stereo PCM.
Wire AmCQuam into the Demodulator enum, add ChannelDsp::cquam_decoder
field initialized for RigMode::AMC, and insert the C-QUAM audio path
between the WFM and fallback branches in process_block. Update all
mode-dispatch tables (agc_for_mode, iq_agc_for_mode, dc_for_mode,
default_bandwidth_for_mode, lib.rs, vchan_impl.rs) with AMC arms.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Drop fir_taps field from SdrChannelConfig and its default. Remove the
SetFirTaps dispatch arm from rig_task. The DSP layer now auto-calculates
tap count from audio_bandwidth_hz.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace the static fir_taps parameter with auto_taps(cutoff_norm) which
computes ceil(3.32 / cutoff_norm).clamp(63, 16383). This ensures the
filter transition band equals one passband width regardless of SDR sample
rate, giving correct image rejection when the user sets audio_bandwidth_hz.
At 912 ksps with 3 kHz audio bandwidth this yields ~2018 taps instead
of the previous hardcoded 64, eliminating the 114 kHz stopband gap that
caused adjacent-band signals to alias into the audio output.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add read_named_gain to IqSource (default: None) and implement it in
RealIqSource via Device::gain_element. Read the "LNA" element before
boxing the source so the initial sdr_lna_gain_db reflects the actual
hardware state, making the UI control visible and correct on first
connect. Devices without an LNA element (e.g. RTL-SDR with "TUNER")
return None and the control stays hidden.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Handle RigCommand::SetSdrLnaGain by calling set_sdr_lna_gain on the
rig and refreshing filter state, matching the pattern used by
SetSdrGain and SetSdrAgc.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add set_named_gain to the IqSource trait and implement it in
RealIqSource via soapysdr Device::set_gain_element. Wire a
lna_gain_cmd channel through SdrPipeline so the IQ read loop applies
LNA gain changes on the next iteration. Add set_sdr_lna_gain to
SoapySdrRig and expose the current value via filter_state.
Co-authored-by: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add hardware AGC on/off control for SoapySDR backend, wired through the
full stack from RigCommand to the web UI:
- RigCommand::SetSdrAgc(bool) + ClientCommand::SetSdrAgc in protocol
- set_sdr_agc() on RigCat trait (not-supported default)
- SoapySdrRig: agc_enabled field, set_sdr_agc() via pipeline agc_cmd,
sdr_agc_enabled in filter_state(); removes the "not yet implemented"
warning — gain_mode="auto" now properly enables hardware AGC via
SoapySDR set_gain_mode()
- IqSource::set_gain_mode() trait method; RealIqSource implements it
- SdrPipeline: agc_cmd channel, read loop applies it each iteration
- POST /set_sdr_agc endpoint in trx-frontend-http
- New "SDR settings" full-row in index.html with Hardware AGC checkbox
and RF Gain (moved out of WFM controls); row hidden when
show_sdr_gain_control is false
- app.js: AGC checkbox handler, disables RF gain input while AGC is on,
syncs checkbox state from filter.sdr_agc_enabled
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Three issues caused audible distortion on AM reception:
1. DC blocker shared r=0.9999 (τ≈1.25 s at 8 kHz) across all modes.
For AM the envelope detector outputs A_c+m(t) — always positive —
so the blocker needs to track the carrier bias quickly. AM now uses
r=0.999 (τ≈125 ms), 10× faster, while keeping the highpass cutoff
below 2 Hz so speech is unaffected.
2. Audio AGC time constants were inverted relative to good AM AGC design:
attack=200 ms (should be fast to prevent overload) and
release=3500 ms (unreasonably sluggish). Changed to attack=5 ms /
release=200 ms, target=0.5, max_gain=36 dB.
3. No IQ AGC before envelope detection meant carrier amplitude variation
went directly into the audio chain, forcing the slow audio AGC to
handle both RF level and audio level simultaneously. Added an AM IQ
AGC (attack=0.5 ms, release=50 ms, target=0.7, max=30 dB) that
normalizes carrier power before demod_am, so the DC blocker always
sees the same steady-state bias regardless of signal strength.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Three bugs caused USB/LSB to sound like AM:
1. The IQ low-pass filter was symmetric (passband ±BW/2), so both
sidebands were passed equally — taking .re then produced DSB-SC
rather than SSB audio.
2. cutoff_hz was computed as bandwidth_hz/2, halving the usable audio
bandwidth (1500 Hz for a 3 kHz USB channel).
3. demod_lsb claimed spectrum inversion was "handled upstream by
negating channel_if_hz", but that negation was never applied; USB
and LSB were functionally identical.
Fix: add a shift_norm parameter to build_fir_kernel / BlockFirFilterPair
that complex-modulates the time-domain FIR coefficients by
e^{j·2π·shift_norm·n}, shifting the passband in the frequency domain.
A new ssb_shift_norm() helper returns +cutoff_norm for USB/CW/DIG
([0, BW] Hz passband) and -cutoff_norm for LSB/CWR ([-BW, 0] Hz
passband); all other modes get 0.0 (symmetric LPF unchanged).
After the one-sided filter, taking .re correctly reconstructs the
selected sideband. No IF negation is needed for LSB.
Also fix two unit tests missing the force_mono_pcm argument introduced
after they were last updated.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Signed-off-by: Stan Grams <sjg@haxx.space>
Use millisecond-based slot indexing for FT4 decode windows in\nforeground and background decoders to avoid premature 7s resets.\n\nCo-authored-by: OpenAI Codex <codex@openai.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Use FT2-specific analysis settings and a wider receive span.
Switch server-side FT2 decoding to a rolling async window.
Widen FT2 candidate timing search in the vendored decoder.
Co-authored-by: OpenAI Codex <codex@openai.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Implement a distinct FT2 protocol path in the decoder stack and align\nits timing with the confirmed FT2 framing used by Decodium.\n\nCo-authored-by: OpenAI Codex <codex@openai.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
sjg
Claude