Add POST endpoints for toggle_aprs_decode, toggle_cw_decode,
clear_aprs_decode, and clear_cw_decode. Add toggle buttons in APRS
and CW tabs. Render decoder enabled state from SSE updates. Clear
button now also resets server-side decoder state.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add SetAprsDecodeEnabled, SetCwDecodeEnabled, ResetAprsDecoder, and
ResetCwDecoder to the JSON TCP frontend command mapping.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Initialize decoder state fields and map new RigCommand/ClientCommand
variants through the remote client TCP bridge.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace HEAD probe with EventSource readyState check to properly
detect 404 vs connection drop. HEAD requests to SSE endpoints may
not behave reliably across all setups.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Log whether audio/decode is enabled at startup and warn when
/decode is requested but the decode channel was not set. Helps
diagnose broken decode pipelines.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
The decode EventSource silently retried on 404 leaving the status
stuck on "Waiting for server decode". Probe /decode first to
distinguish 404 (audio disabled) from real SSE errors and update
the APRS/CW status text accordingly.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Server-side decoding makes client-side decoders redundant. Remove
~1000 lines of browser-side Bell 202 AFSK, AX.25/APRS parsing, and
Goertzel CW decoding. The frontend now relies solely on the /decode
SSE endpoint for decoded data.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Clears the packet list, map markers are unaffected. Also wipes
the persisted packet history from localStorage.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add /decode SSE endpoint streaming decoded messages from the server.
Add decode channel OnceLock with set/subscribe pattern.
In the browser, connect to /decode EventSource and dispatch to
onServerAprs/onServerCw handlers. APRS and CW plugins now receive
server-decoded data automatically while keeping browser-side decoding
as a fallback.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Handle APRS/CW decode message types (0x03/0x04) in audio_client,
deserialize and forward via broadcast channel. Create decode channel
and pass to audio client and HTTP frontend.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add localStorage persistence (trx_ prefix) for UI settings:
- Jog step, RX/TX volume (app.js)
- CW WPM, tone, threshold, auto-detect flags (cw.js)
- APRS decoded packets and running state (aprs.js)
APRS decoder auto-restarts on page refresh if it was active,
and all decoded packets plus map markers are restored from storage.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Render non-ASCII characters in decoded APRS info text as yellow
[0xNN] hex tags. Printable ASCII is HTML-escaped to prevent XSS.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Show the proper APRS symbol sprite icon on map markers instead of
generic green circles. Falls back to a green circle marker when no
symbol info is available.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add a Map sub-tab under Plugins that displays an interactive
OpenStreetMap via Leaflet.js showing:
- Receiver location (blue marker) from server config lat/lon
- APRS station positions (green markers) updated in real-time
The map lazy-initializes on first tab switch, handles tile rendering
on tab visibility changes, and deduplicates station markers by
callsign. Also includes the fallback snapshot lat/lon fields in the
API layer.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Map server_latitude and server_longitude from RigSnapshot to RigState
in remote_client and set None defaults in standalone client init.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
- Add APRS symbol icons using hessu/aprs-symbols sprite sheets
- Parse uncompressed and compressed position formats for lat/lon
- Render clickable OpenStreetMap links for position packets
- Replace delay-and-multiply discriminator with mark/space correlation
detector for more robust AFSK decoding
- Reduce PLL gain from 0.7 to 0.4 for stable clock recovery
- Move plugin JS files to plugins/ subdirectory
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add Auto checkboxes (checked by default) next to WPM and Tone inputs.
Auto Tone uses a multi-bin Goertzel scan across 300-1200 Hz with
stability tracking. Auto WPM collects on-durations in a rolling buffer
and uses k-means-style clustering to separate dits from dahs.
Unchecking Auto allows manual control.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Extract the APRS decoder from app.js into its own aprs.js file and add
a new CW (Morse code) decoder plugin in cw.js. The CW decoder uses a
Goertzel tone detector with configurable WPM, tone frequency, and
signal threshold. The Plugins tab now has three sub-tabs: Overview,
APRS, and CW.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace bandpass filter envelope detector with delay-and-multiply
frequency discriminator. Add biquad bandpass pre-filter centered at
1700 Hz to remove out-of-band noise. Replace IIR low-pass with
moving-average LPF over half a bit period, which places a null at
2x mark frequency for clean discriminator artifact removal.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace the coherent correlation detector with a non-coherent
bandpass filter + envelope detection approach for significantly
better frequency discrimination between mark (1200Hz) and space
(2200Hz) tones. Uses two cascaded 2nd-order IIR biquad filters
per tone with IIR-smoothed envelope detection.
Replace hard clock reset with PLL-style gradual correction for
smoother bit timing recovery.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add silence detection that resets the demodulator state when RMS
drops below threshold, so burst-mode APRS packets after squelch
activation start with a clean correlator and clock recovery.
Display CRC-failing frames at reduced opacity with a [CRC] tag to
aid debugging. Enhanced CRC-fail console logging now includes
attempted address decode, bit count, and hex dump.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Assign green to VFO A, yellow to VFO B, and deterministic hues
to additional VFOs. The active VFO color is also applied to the
main frequency display. Rework the header title to show
"trx-rs <version> @ <callsign>'s <rig>" instead of "<rig> status".
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Fix three bugs in the Bell 202 AFSK demodulator preventing frame
decoding:
- Separate NRZI state from clock recovery (shared lastBit variable
caused NRZI to always output 1)
- Buffer 1-bits in ones counter instead of pushing to frameBits
immediately, preventing flag/stuff bits from contaminating frame
data and corrupting byte alignment
- Detect flags via ones-count on decoded bits instead of shift
register on raw bits
Also add framed packet log container styling, remove redundant
description text, and add debug counters logging pipeline health
to the browser console.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace server-side /frontends endpoint with client-side plugin system.
The Plugins tab now has Overview and APRS sub-tabs. The APRS plugin
decodes packets from RX audio using Bell 202 AFSK demodulation (1200
baud), AX.25 frame decoding with NRZI/HDLC, and CRC-16-CCITT
validation. Decoded packets are displayed in a scrolling log.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add GET /frontends API endpoint returning registered frontend names as
JSON. Add Plugins tab to the web UI that fetches and displays the list.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Close #tab-main properly so the footer and About tab are not nested
inside it — footer is now visible on all tabs.
Add server address, rig connection method, supported modes, and VFO
count to the About tab.
Move logo from translucent centered overlay to solid image in the
top-right of the header.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Add a tab bar to the HTTP frontend card. All existing controls stay in
the Main tab. A new About tab shows server version, callsign, rig info,
client version, and connected client count, updated live via SSE.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Return 204 for non-WebSocket GET requests to /audio instead of
letting actix-ws reject with 400. This allows the browser's audio
availability probe to work correctly.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Replace the rolling canvas signal graph with a practical signal
measurement feature. The operator can start/stop measurement to
collect signal samples, then view averaged and peak S-unit results.
Also fix signal display to correctly convert dBm wire format to
S-units using standard S-meter scale (S1=-121dBm, S9=-73dBm,
6dB per S-unit).
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
- Make server callsign a clickable link to qrzcq.com
- Center frequency input text and use DSEG14 Classic font
- Include callsign in page title (e.g. N0CALL - trx-frontend-http v0.1.0)
- Block jog wheel when rig lock is active
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
Load DSEG14 Classic 14-segment LCD font from CDN and apply it to
the frequency input at 2x size for a realistic radio display look.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
- Add RX/TX volume sliders with GainNode audio chain integration,
scroll wheel support, and percentage display
- Display server callsign and version from SSE event data
- Merge TX Limit hint into its label line
- Add copyright footer with link to haxx.space
- Uniform section spacing via flex gap on #content
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Signed-off-by: Stanislaw Grams <stanislawgrams@gmail.com>
sjg